Author Topic: ew350 flywheel extractor  (Read 788 times)

0 Members and 1 Guest are viewing this topic.

Offline Neilj

  • Full Member
  • **
  • Join Date: May 2021
  • Posts: 39
  • Location: Newport, UK
ew350 flywheel extractor
« on: 18 Jun 2021 at 12:28 »
Anyone in Newport or bristol got a flywheel extractor i could borrow. Could bring my engine around and do it there and then if that would be ok.Bit cheeky i know. 
 

Offline jimf

  • Member
  • *
  • Join Date: Jun 2021
  • Posts: 10
  • Location: Luton, UK
Re: ew350 flywheel extractor
« Reply #1 on: 05 Jul 2021 at 21:28 »
Has the club any for sale.and how much

Offline Neilj

  • Full Member
  • **
  • Join Date: May 2021
  • Posts: 39
  • Location: Newport, UK
Re: ew350 flywheel extractor
« Reply #2 on: 07 Jul 2021 at 10:32 »
Might be usefull info.held the engine minus head and pistons just off the bench nice and horizontal by the flywheel while my son took a aluminiam dowl 30mm and gave the crank one decent tap.The engine droped straight onto my rag pile no problem.Just one sharp metal to metal tap,metal hammer used as well.

Offline tck

  • Senior Member
  • ***
  • Join Date: Jul 2004
  • Posts: 357
    • old racer
Re: ew350 flywheel extractor
« Reply #3 on: 31 Jul 2021 at 14:08 »
I made the most massive extractor to no avail (see New Con Rod and on this forum )in the end a small extractor did the job, the secret? lots and lots of heat

Offline Daren W Australia

  • Master Member
  • ****
  • Join Date: Apr 2005
  • Posts: 601
  • Location: Sydney Australia
Re: ew350 flywheel extractor
« Reply #4 on: 31 Jul 2021 at 22:35 »
Hi
I had to remove 4 last week 3 others basically fell of with a sharp tap the fourth I used this set up i tightened it to 3 dugga dugga on my cheap rattle gun came ack an hour latter and gave it a sharp blow with a lump hammer.
Ta Daren





Image orientation fixed and converted to linked files - Dave, 02Aug2021
« Last Edit: 02 Aug 2021 at 02:46 by Dave »
too many dougli not enough time!

Offline Neilj

  • Full Member
  • **
  • Join Date: May 2021
  • Posts: 39
  • Location: Newport, UK
Re: ew350 flywheel extractor
« Reply #5 on: 01 Aug 2021 at 17:55 »
Loving the technical 3 Duggar Duggar.Do us a favour can you measure the thickness of ring on the flywheel that mates with the clutch release/thrust bearing.Im making one got the inside and outside by measuring,but can only guess the thickness from photo,s like yours.Cheers Neil

Offline Daren W Australia

  • Master Member
  • ****
  • Join Date: Apr 2005
  • Posts: 601
  • Location: Sydney Australia
Re: ew350 flywheel extractor
« Reply #6 on: 03 Aug 2021 at 01:50 »
Hi Neil I get 190 thou but its pretty crusty also it will depend on your taper and how many times its been lapped ta Daren







Images converted to linked files - Dave,14Aug2021
« Last Edit: 13 Aug 2021 at 21:35 by Dave »
too many dougli not enough time!

Offline Neilj

  • Full Member
  • **
  • Join Date: May 2021
  • Posts: 39
  • Location: Newport, UK
Re: ew350 flywheel extractor
« Reply #7 on: 03 Aug 2021 at 05:38 »
Thanks itís the ring on the flywheel side the one the balls rub up against is the one I need the width please.thanks Neil