Author Topic: rebuilding 1927 EW  (Read 4699 times)

0 Members and 1 Guest are viewing this topic.

Offline bikerdude

  • Member
  • *
  • Join Date: Dec 2006
  • Posts: 3
rebuilding 1927 EW
« on: 05 Dec 2006 at 20:04 »
I'm rebuilding a 1927 EW and was talking to a fellow owner today. He has stopped riding his as he is afraid of the poor brakes, especially the front. His view is you couldn't lock the wheel on wet ice! Now I 'm worried. Is there a way of setting up or modifying the brakes to give an adequate performance? Can a Rudge 8" or similar brakeplate be inserted to give better performance?  Would like some comments or suggestions.  Don't the 500, 600 and 750cc bikes have virtually the same brake? Surely this means that you can get an adequate performance from the Douglas item? 


Inertia Dynamometer, Dynamometer.

Dynomec  is a Finland based dynamometer manufacturing company.  Dynomec offers dynamometers for workshop, garage, motorcycle club etc.  Dynomec also offers dynamometer software.

Offline Ian

  • Master Member
  • ****
  • Join Date: Jul 2004
  • Posts: 1288
  • Location: The Oaks, NSW, Australia
Re: rebuilding 1927 EW
« Reply #1 on: 05 Dec 2006 at 21:51 »
The brakes on the EW are more than adequate if set up correctly - quite good for their time. It is VERY important to make sure that the band adjustments are done properly - my understanding is that there should be minimal clearance. I have the same brakes on my OC600 - so far it would seem that I have one adjusted well and the other still needs work !!

Offline Stuart Lister

  • Full Member
  • **
  • Join Date: May 2004
  • Posts: 60
  • Location: UK (East Yorks)
Re: rebuilding 1927 EW
« Reply #2 on: 05 Dec 2006 at 23:24 »
Hi there,

I finished the rebuild of my '26 EW this Summer, and I have done around four hundred miles since. Like you, I had heard all sorts of bad things about the brakes, but guess what? they're all right. The back is definitely better than the front, and even then you have to put some effort into it, but don't forget, it's only a short lever, you can't expect it to be a light touch. The front brake is of course exactly the same, but it suffers from having that short inverted handlebar lever. It works, but you do have to pull on that lever, (forearms like Popeye would help!)

It's also worth remembering that in the 1920s lots of manufacturers didn't fit a front brake at all, and those that did believed it was just there to assist the back one a bit.

When you get the linings done, ask for the softest possible material. Lets face it, we don't put enough miles on these old bikes to have to worry about longevity, let's just buy the material that works best. I had mine done at Safetek in Bradford here in the UK; they were not expensive, and I had them back in well under a week.

As for fitting a different brake plate, I doubt if it's worth the effort. The limiting factor is not the brake band itself, but the thin steel drums. As the brake band expands, the drum warms up and distorts. A different brake plate would not change that.

Having said all that, mine passed it's MOT without the tester having to make any allowance for it's age, so they can't be all that bad can they?

Good luck, enjoy,


Offline graeme

  • Master Member
  • ****
  • Join Date: Oct 2004
  • Posts: 621
  • Location: Hobart, Australia
Re: rebuilding 1927 EW
« Reply #3 on: 06 Dec 2006 at 07:21 »
I can concur with Ian and Stuart - the brakes on my S6 were terrible before I set them up properly, but now they are really quite good. They certainly compare favourably with other machines of the era - notably AJS, their brakes are bloody awful!